Back to All Modules
Permits to Work

Hot Work Permit

Hot work permits for welding, cutting, brazing, and grinding, with the 35-foot check, fire watch sign-off, and post-work monitoring recorded on a phone.

What is Hot Work Permit?

Most hot work fires don't start while the welder is still under the hood. They start an hour or two later, when a spark that dropped through a floor opening or settled into pipe insulation finally finds enough air. By then the crew has packed up and nobody is looking. A hot work permit exists to close that gap, and SiteChief puts the permit on a phone so the checks are done at the work location instead of in the trailer afterward.

Before the permit is issued, the person authorizing the work goes through the precautions in 29 CFR 1910.252(a) and, on construction jobs, 1926.352. Are combustibles moved at least 35 feet away or shielded? Are floor and wall openings covered? Is the right extinguisher within reach, and is the sprinkler system in service? If detection or suppression has to be impaired for the job, the permit records who took it out and who is responsible for putting it back. The fire watch is named on the permit, so there's no question later about who was assigned.

The permit stays open after the torch goes out. OSHA requires a fire watch for at least 30 minutes after welding or cutting ends. Current editions of NFPA 51B call for a longer watch, and many property insurers ask for further monitoring of the area for several hours on top of that. You set the monitoring period your program or your insurer requires, and SiteChief reminds the fire watch to make each check and record it before the permit can be closed.

Regulatory Compliance

  • • 29 CFR 1910.252(a) - Welding, Cutting, and Brazing: Fire Prevention and Protection
  • • 29 CFR 1926.352 - Fire Prevention in Construction Welding and Cutting
  • • NFPA 51B - Fire Prevention During Welding, Cutting, and Other Hot Work
  • • Property insurer hot work permit requirements
Hot Work Permit Checklist
Hot work pre-work checklist built around 1910.252(a) and NFPA 51B precautions
35-foot combustible clearance and shielding verification with photo evidence
Fire extinguisher type and location recorded on the permit
Fire watch assignment based on the hazards at the work location
Post-work monitoring schedule with reminders for each check
Fire alarm and sprinkler impairment and restoration tracking

Key Benefits

Catch smoldering fires during the hours after work stops, when most hot work fires actually start

A named fire watch on every permit, with their sign-off recorded

Monitoring periods set to the OSHA minimum, NFPA 51B, or your insurer's longer requirement

Completed permits with photos ready to show your insurer or an OSHA compliance officer

The 35-foot combustibles check done and photographed at the work location, not from memory

Impaired alarms and sprinklers tracked until someone confirms they're back in service

Features & Capabilities

Hot work pre-work checklist built around 1910.252(a) and NFPA 51B precautions

35-foot combustible clearance and shielding verification with photo evidence

Fire extinguisher type and location recorded on the permit

Fire watch assignment based on the hazards at the work location

Post-work monitoring schedule with reminders for each check

Fire alarm and sprinkler impairment and restoration tracking

Emergency contacts and response procedures on the permit

Works as part of the main SiteChief permit to work system

How It Works

1

Identify the hot work and request a permit from the phone or the web app

2

Complete the fire prevention checklist, including the 35-foot combustibles check

3

Confirm extinguishers, sprinkler status, and the assigned fire watch

4

Get authorization and start work with the fire watch in place

5

Record post-work monitoring checks, then close out the permit

Frequently asked questions

What is Hot Work Permit?
Hot work permits for welding, cutting, brazing, and grinding, with the 35-foot check, fire watch sign-off, and post-work monitoring recorded on a phone.
How does Hot Work Permit work?
Identify the hot work and request a permit from the phone or the web app. Complete the fire prevention checklist, including the 35-foot combustibles check. Confirm extinguishers, sprinkler status, and the assigned fire watch. Get authorization and start work with the fire watch in place. Record post-work monitoring checks, then close out the permit.
What are the main benefits of Hot Work Permit?
Catch smoldering fires during the hours after work stops, when most hot work fires actually start. A named fire watch on every permit, with their sign-off recorded. Monitoring periods set to the OSHA minimum, NFPA 51B, or your insurer's longer requirement. Completed permits with photos ready to show your insurer or an OSHA compliance officer.
Which regulations does Hot Work Permit help you comply with?
29 CFR 1910.252(a) - Welding, Cutting, and Brazing: Fire Prevention and Protection. 29 CFR 1926.352 - Fire Prevention in Construction Welding and Cutting. NFPA 51B - Fire Prevention During Welding, Cutting, and Other Hot Work. Property insurer hot work permit requirements.

Ready to Use Hot Work Permit?

Start managing your health and safety with our comprehensive solution.

30-day free trial · Cancel anytime

We use cookies. Essential ones are on. Optional ones need your OK.